Order from us for quality, customized work in due time of your choice.
Concrete Bricks
Concrete Bricks are manufactured under the BSI Kitemark Licensee with specification to BS 6073. The Specification and Workmanship of Concrete Bricks are based on:
Location Reference: Depends on where the Brick is intended to use. For eg: Earthquake resistant building, Moisture resistant Building or Weather Proof Buildings.
Work Size: The standard size of Concrete Bricks is 215X103X65 mm. The Modular sizes of concrete bricks are 290X90X90; 190X90X90; 190X90X60 which are manufactured to close tolerances on site and achieve configuration.
Type/ Color/ Texture: Pale Grey is the natural color though a variety of colors like Red, Green or black can be obtained by addition of Pigments. It can also be made Solid, Perforated or Fogged depending on the Construction Requirements.
Constituents: Concrete Bricks are manufactured of Blended Dense Aggregates. Cement is mixed with 89% of pigmented Iron Oxide Particles to give the desired color to form a matrix of concrete with fine finish.
Weight and Structural Compatibility: The Concrete Bricks are 3.2 kgs. The Strength of Engineered Concrete Bricks is 40 MPa. The Brick will be Sulphate resistant Portland or equivalent cement constituency of 350kg/cu.m. (BS 6073 -2:1981)
Water Absorption: Less than 7% for about 24 hours of cold water immersion. This makes it suitable for excessive damp conditions, retaining walls etc.
Moisture and Thermal Movement: Concrete bricks have an average shrinkage of 0.04 0.06%. Concrete Bricks are initially wetted to prevent water retention and suction.
Thermal Conductivity: 1.4-1.8 W/mK.
Fire Resistance: Concrete Bricks are designed as per the requirements of Euro Class A1 in terms of Fire Resistance.
Compression Strength: Facing Bricks Compression Strength ranges from 15 N/sq.m
Manufacturers Reference: The Concrete Bricks should obtain the BSI Kitemark Licensee and the final products should meet the standards of the British Board of Agreement Supplement to the Approved Documents supporting the Building Regulations of 1991.
Concrete Blocks: Load Bearing Walls and Partition Walls
As per the Specification and Workmanship specified in BS 6073, the Concrete Blocks for load bearing blocks are based on:
Location Reference: Concrete Blocks are manufactured as Solid, Hollow or Cellar as per the requirements of the building.
Size and Shapes: Concrete Blocks are manufactured to the standard size of 440X40mm, but can be seen exceedingly in different sizes to fit various designs. The sizes are: 440X140,140X214, 440X430,540X440,610X140,610X215,610X270,620X215,620X300 and 620X430.
Compressive Strength: Concrete Blocks have Compressive Strength ranging from 2.8 to 30 MPa.
Density: The density of each concrete block is 420 2200kg/cu.m.
Thermal Conductivity: Thermal conductivity ranges from 0.10-1.5 W/mK with 3% moisture content.
Types and Finishes: Naturally finished blocks are of grey color and buff but can be changed as per the requirements and addition of Pigments.
Constituents: Concrete Blocks are manufactured of natural dense aggregates like gravel, limestone and crushed granite. Aerated Concrete Blocks are made by addition of Aluminum to Sand, Lime, Fly ash and Portland cement.
Fire Resistance: Load bearing un-plastered Concrete Block with 90mm walls gives 60 minutes resistance and 150 215 mm thick Concrete Blocks can resist for about 360 minutes.
Manufacturing levels: Concrete Blocks are manufactured of extended dense aggregates, made into moulds and cured for about 28 days. Aerated Blocks are constructed by adding Aluminum and forming a non cellular structure and then cured in an Autoclave.
Manufacturers Reference: The Concrete Blocks are constructed according to BS 6073 specifications with BSI Kite mark Licensee and should meet the regulations of the British Board of Agreement Supplement to the Approved Documents supporting the Building Regulations of 1991.
Concrete Blocks: Non load Bearing Walls
Concrete Blocks manufactured for Non Load Bearing Walls follow the specifications as of BS 6073 Part 1.
The Specifications are based on:
Location Reference: Non Load bearing walls can be constructed as Cavity walls which are constructed as 2 sheet walls with each wall 100mm thick.
Work Size: Concrete Blocks with 75mm or less than 75 mm are classified as non load bearing blocks.
Strength: 0.65 N/sq.mm is the average transverse strength.
Density: 900 kg/cu.m.
Fire Resistance: The non load bearing cavity walls can resist fire for 240 minutes.
Finish: The finishes are made standard as per the suitability of the non load bearing walls.
Manufacturer references: Manufacturers are considered from the British Board of Agreement Supplement to the Approved Documents supporting the Building Regulations of 1991. The products should be made under the licensee of BSI Kite mark Licensee and should meet the standards of Building Regulations.
The workmanship of Concrete walls whether constructed of Concrete Bricks , Concrete Blocks for Load Bearing Walls or Concrete Blocks for non load bearing walls have to meet the standards of BS EN ISO 9000, Quality Management systems and standards set forward by the British Building Regulations. The Workmanship can also be confirmed by the regulations of National Technical Specification set formed by member states which act as contracting parties to the Europe Economic Area. The technical Standards of the Concrete Blocks or Bricks should comply with the National or European Standards Certificate confirmed by the European Technical Approvals made by the concerning European Body. The work should also be approved by the European Organization of Technical Approvals(EOTA) and the work should be equivalent to the regulations. The workmanship can also be approved based on the experience of the contractor and experiences that the concrete blocks and bricks meet the standards and perform the function.
References
-
Laxtons General Specification for Major Building and Civil Engineering Projects. Butterworth-Heinemann Linacre House. Reed Educational and Professional Publishing.
-
Lyons, Arthur. Materials for architects and builders .3rd ed. Butterworth-Heinemann. 2007
-
Eurocode 6: Design of Masonry Structures . 2007. Web.
Order from us for quality, customized work in due time of your choice.